View AD7863ARS-10REEL_5208837.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

simultaneous sampling dual 175 ksps 14-bit adc ad7863 rev. b information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2006 analog devices, inc. all rights reserved. features two fast 14-bit adcs four input channels simultaneous sampling and conversion 5.2 s conversion time single supply operation selection of input ranges 10 v for ad7863-10 2.5 v for ad7863-3 0 v to 2.5 v for ad7863-2 high speed parallel interface low power, 70 mw typical power saving mode, 105 w maximum overvoltage protection on analog inputs 14-bit lead compatible upgrade to ad7862 general description the ad7863 is a high speed, low power, dual 14-bit analog-to- digital converter that operates from a single 5 v supply. functional block diagram dgnd db0 busy cs convst ad7863 2k? agnd agnd v dd v ref db13 a0 track/ hold track/ hold mux 2.5v reference output latch rd conversion control logic signal scaling signal scaling signal scaling mux 14-bit adc 14-bit adc clock v a2 v b2 v a1 v b1 signal scaling 06411-001 figure 1. the part contains two 5.2 s su ccessive approximation adcs, two track/hold amplifiers, an internal 2.5 v reference and a high speed parallel interface. four analog inputs are grouped into two channels (a and b) selected by the a0 input. each channel has two inputs (v a1 and v a2 or v b1 and v b2 ) that can be sampled and converted simultaneously, thus preserving the relative phase information of the signals on both analog inputs. the part accepts an analog input range of 10 v (ad7863-10), 2.5 v (ad7863-3), and 0 v to 2.5 v (ad7863-2). overvoltage protection on the analog inputs for the part allows the input voltage to go to 17 v, 7 v, or +7 v respectively, without causing damage. a single conversion start signal ( convst ) simultaneously places both track/holds into hold and initiates conversion on both channels. the busy signal indicates the end of conversion and at this time the conversion results for both channels are available to be read. the first read after a conversion accesses the result from v a1 or v b1 , and the second read accesses the result from v a2 or v b2 , depending on whether the multiplexer select (a0) is low or high, respectively. data is read from the part via a 14-bit parallel data bus with standard cs and rd signals. in addition to the traditional dc accuracy specifications such as linearity, gain, and offset errors, the part is also specified for dynamic performance parameters including harmonic distortion and signal-to-noise ratio. the ad7863 is fabricated in the analog devices, inc. linear compatible cmos (lc 2 mos) process, a mixed technology process that combines precision bipolar circuits with low power cmos logic. it is available in 28-lead soic_w and ssop. product highlights 1. the ad7863 features two complete adc functions allowing simultaneous sampling and conversion of two channels. each adc has a two-channel input mux. the conversion result for both channels is available 5.2 s after initiating conversion. 2. the ad7863 operates from a single 5 v supply and consumes 70 mw typical. the automatic power-down mode, where the part goes into power-down once conversion is complete and wakes up before the next conversion cycle, makes the ad7863 ideal for battery- powered or portable applications. 3. the part offers a high speed parallel interface for easy connection to microprocessors, microcontrollers, and digital signal processors. 4. the part is offered in three versions with different analog input ranges. the ad7863-10 offers the standard industrial input range of 10 v; the ad7863-3 offers the common signal processing input range of 2.5 v, while the ad7863-2 can be used in unipolar 0 v to 2.5 v applications. 5. the part features very tight aperture delay matching between the two input sample and hold amplifiers.
ad7863 rev. b | page 2 of 24 table of contents features .............................................................................................. 1 general description ......................................................................... 1 functional block diagram .............................................................. 1 product highlights ........................................................................... 1 revision history ............................................................................... 2 specifications..................................................................................... 3 timing characteristics ................................................................ 5 absolute maximum ratings............................................................ 6 esd caution.................................................................................. 6 pin configuration and function descriptions............................. 7 terminology ...................................................................................... 8 converter details.............................................................................. 9 track-and-hold section .............................................................. 9 reference section ......................................................................... 9 circuit description......................................................................... 10 analog input section ................................................................. 10 offset and full-scale adjustment ............................................ 10 timing and control ................................................................... 11 operating modes ............................................................................ 13 mode 1 operation ...................................................................... 13 mode 2 operation ...................................................................... 13 ad7863 dynamic specifications ............................................. 14 signal-to-noise ratio (snr)..................................................... 14 effective number of bits ........................................................... 14 total harmonic distortion (thd) .......................................... 15 intermodulation distortion ...................................................... 15 peak harmonic or spurious noise........................................... 15 dc linearity plot ....................................................................... 15 power considerations................................................................ 16 microprocessor interfacing........................................................... 17 ad7863 to adsp-2100 interface ............................................. 17 ad7863 to adsp-2101/adsp-2102 interface ....................... 17 ad7863 to tms32010 interface .............................................. 17 ad7863 to tms320c25 interface............................................ 17 ad7863 to mc68000 interface ................................................ 18 ad7863 to 80c196 interface .................................................... 18 vector motor control ................................................................ 18 multiple ad7863s ...................................................................... 19 applications hints.......................................................................... 20 pc board layout considerations............................................. 20 ground planes ............................................................................ 20 power planes ............................................................................... 20 supply decoupling ..................................................................... 20 outline dimensions ....................................................................... 21 ordering guide .......................................................................... 22 revision history 11/06rev. a to rev. b updated format..................................................................universal deleted applications ........................................................................ 1 changes to specifications ................................................................ 3 changes to absolute maximum ratings ....................................... 6 updated outline dimensions ....................................................... 21 changes to ordering guide .......................................................... 22 5/99rev. 0 to rev. a
ad7863 rev. b | page 3 of 24 specifications v dd = 5 v 5%, agnd = dgnd = 0 v, ref = internal. all specifications t min to t max , unless otherwise noted. table 1. parameter a version 1 b version 1 unit test conditions/comments sample and hold ?3 db small signal bandwidth 7 7 mhz typ aperture delay 2 35 35 ns max aperture jitter 2 50 50 ps typ aperture delay matching 2 350 350 ps max dynamic performance 3 f in = 80.0 khz, f s = 175 ksps signal-to-(noise + distortion) ratio 4 @ 25c 78 78 db min t min to t max 77 77 db min total harmonic distortion 4 ?82 ?82 db max ?87 db typ peak harmonic or spurious noise 4 ?82 ?82 db max ?90 db typ intermodulation distortion 4 fa = 49 khz, fb = 50 khz second order terms ?93 ?93 db typ third order terms ?89 ?89 db typ channel-to-channel isolation 4 ?86 ?86 db typ f in = 50 khz sine wave dc accuracy any channel resolution 14 14 bits minimum resolution for which no missing codes are guaranteed 14 14 bits relative accuracy 4 2.5 2 lsb max differential nonlinearity 4 +2 to ?1 +2 to ?1 lsb max ad7863-10, ad7863-3 positive gain error 4 10 8 lsb max positive gain error match 4 10 10 lsb max negative gain error 4 10 8 lsb max negative gain error match 4 10 10 lsb max bipolar zero error 10 8 lsb max bipolar zero error match 8 6 lsb max ad7863-2 positive gain error 4 14 lsb max positive gain error match 4 16 lsb max unipolar offset error 14 lsb max unipolar offset error match 10 lsb max analog inputs ad7863-10 input voltage range 10 10 v input resistance 9 9 k typ ad7863-3 input voltage range 2.5 2.5 v input resistance 3 3 k typ ad7863-2 input voltage range 2.5 2.5 v input current 100 100 na max
ad7863 rev. b | page 4 of 24 parameter a version 1 b version 1 unit test conditions/comments reference input/output ref in input voltage range 2.375 to 2.625 2.375 to 2.625 v 2.5 v 5% ref in input current 100 100 a max ref out output voltage 2.5 2.5 v nom ref out error @ 25c 10 10 mv max ref out error t min to t max 20 20 mv max ref out temperature coefficient 25 25 ppm/c typ logic inputs input high voltage, v inh 2.4 2.4 v min v dd = 5 v 5% input low voltage, v inl 0.8 0.8 v max v dd = 5 v 5% input current, i in 10 10 a max input capacitance, c in 5 10 10 pf max logic outputs output high voltage, v oh 4.0 4.0 v min i source = 200 a output low voltage, v ol 0.4 0.4 v max i sink = 1.6 ma db11 to db0 floating-state leakage current 10 10 a max floating-state capacitance 5 10 10 pf max output coding ad7863-10, ad7863-3 twos complement ad7863-2 straight (natural) binary conversion rate conversion time mode 1 operation 5.2 5.2 s max for both channels mode 2 operation 6 10.0 10.0 s max for both channels track/hold acquisition time 4 , 7 0.5 0.5 s max power requirements v dd 5 5 v nom 5% for specified performance i dd normal mode (mode 1) ad7863-10 18 18 ma max ad7863-3 16 16 ma max ad7863-2 11 11 ma max power-down mode (mode 2) i dd @ 25c 8 20 20 a max 40 na typ. logic inputs = 0 v or v dd power dissipation normal mode (mode 1) ad7863-10 94.50 94.50 mw max v dd = 5.25 v, 70 mw typ ad7863-3 84 84 mw max v dd = 5.25 v, 70 mw typ ad7863-2 57.75 57.75 mw max v dd = 5.25 v, 45 mw typ power-down mode @ 25c 105 105 w max 210 nw typ, v dd = 5.25 v 1 temperature ranges are as follows: a version and b version, ?40c to +85c. 2 sample tested during initial release. 3 applies to mode 1 operation. see operating modes section. 4 see terminology section. 5 sample tested @ 25c to ensure compliance. 6 this 10 s includes the wake-up time from standby. this wake-up time is timed from the rising edge of convst , whereas conversion is timed from the falling edge of convst , for a narrow convst pulse width the conversion time is effectively the wake-up time plus conversion time, 10 s. this can be seen from figure 6. n ote that if the convst pulse width is greater than 5.2 s, the effective conversion time increases beyond 10 s. 7 performance measured through full channel (multiplexer, sha, and adc). 8 for best dynamic performance of the ad7863, ate device testing ha s to be performed with power supply decoupling in place. in t he ad7863 power-down mode of operation, the leakage current associated with these decoupling capacitors is greate r than that of the ad7863 supply current. t herefore, the 40 na typical figure shown is characterized and guaranteed by design figure, which reflects the supply curr ent of the ad7863 without decoupling in place. the maximum figure shown in the conditions/comments column reflects the ad7863 with supply decoupling in plac e0.1 f in parallel with 10 f disc ceramic c apacitors on the v dd pin and 2 0.1 f disc ceramic capacitors on the v ref pin, in both cases to the agnd plane.
ad7863 rev. b | page 5 of 24 timing characteristics v dd = 5 v 5%, agnd = dgnd = 0 v, ref = internal. all specifications t min to t max , unless otherwise noted. table 2. parameter 1 , 2 a, b versions unit test conditions/comments t conv 5.2 s max conversion time t acq 0.5 s max acquisition time parallel interface t 1 0 ns min cs to rd setup time t 2 0 ns min cs to rd hold time t 3 35 ns min convst pulse width t 4 45 ns min rd pulse width t 5 3 30 ns min data access time after falling edge of rd t 6 4 5 ns min bus relinquish time after rising edge of rd 30 ns max t 7 10 ns min time between consecutive reads t 8 400 ns min quiet time 1 sample tested at 25c to ensure compliance. all input signals are measured with tr = tf = 1 ns (10% to 90% of 5 v) and timed f rom a voltage level of 1.6 v. 2 see figure 2. 3 measured with the load circuit of figure 3 and defined as the time required for an output to cross 0.8 v or 2.0 v. 4 these times are derived from the measured time taken by the data outputs to change 0.5 v when loaded with the circuit of figur e 3. the measured number is then extrapolated back to remove the effects of charging or discharging the 50 pf capacitor. this means that the times quoted in the timing characteristics are the true bus relinquish times of the part and as such are independent of external bus loading capacitances. v a1 v a2 v b1 v b2 convst busy a0 cs rd data t conv = 5.2s 06411-002 t 3 t 8 t acq t 1 t 4 t 2 t 5 t 6 t 7 figure 2. timing diagram to output pin 1.6ma 200a 50pf 06411-003 figure 3. load circuit for access time and bus relinquish time
ad7863 rev. b | page 6 of 24 absolute maximum ratings t a = 25c, unless otherwise noted. table 3. parameter ratings v dd to agnd ?0.3 v to +7 v v dd to dgnd ?0.3 v to +7 v analog input voltage to agnd ad7863-10 17 v ad7863-3 7 v ad7863-2 7 v reference input voltage to agnd ?0.3 v to v dd + 0.3 v digital input voltage to dgnd ?0.3 v to v dd + 0.3 v digital output voltage to dgnd ?0.3 v to v dd + 0.3 v operating temperature range commercial (a version and b version) ?40c to +85c storage temperature range ?65c to +150c junction temperature 150c soic package, power dissipation 450 mw ja thermal impedance 71.40c/w jc thermal impedance 23.0c/w lead temperature, soldering vapor phase (60 sec) 215c infrared (15 sec) 220c ssop package, power dissipation 450 mw ja thermal impedance 109c/w jc thermal impedance 39.0c/w lead temperature, soldering vapor phase (60 sec) 215c infrared (15 sec) 220c stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. esd caution
ad7863 rev. b | page 7 of 24 pin configuration and fu nction descriptions 28 27 26 25 24 23 22 21 20 19 18 17 16 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 db1 db2 db3 db4 db5 db6 convst db12 db11 db10 db9 dgnd db7 db8 v a2 v ref a0 cs db13 agnd v b1 v a1 rd busy v dd v b2 agnd db0 06411-004 ad7863 top view (not to scale) figure 4. pin configuration table 4. pin function descriptions pin no. mnemonic description 1 to 6 db12 to db7 data bit 12 to data bit 7. three-state ttl outputs. 7 dgnd digital ground. ground reference for digital circuitry. 8 convst convert start input. logic input. a high-to-low transition on this input puts both trac k/holds into their hold mode and starts conversion on both channels. 9 to 15 db6 to db0 data bit 6 to da ta bit 0. three-state ttl outputs. 16 agnd analog ground. ground reference for mux, track/hold, reference, and dac circuitry. 17 v b2 input number 2 of channel b. analog input voltage rang es of 10 v (ad7863-10), 2.5 v (ad7863-3), and 0 v to 2.5 v (ad7863-2). 18 v a2 input number 2 of channel a. analog input voltage rang es of 10 v (ad7863-10), 2.5 v (ad7863-3), and 0 v to 2.5 v (ad7863-2). 19 v ref reference input/output. this pin is connected to the internal reference through a series resistor and is the output reference source for the analog-to-digital converter. the nominal reference voltage is 2.5 v, and this appears at the pin. 20 a0 multiplexer select. this input is used in conjunction with convst to determine on which pair of channels the conversion is to be performed. if a0 is low wh en the conversion is initiated, then channels v a1 and v a2 are selected. if a0 is high when the conversion is initiated, channels v b1 and v b2 are selected. 21 cs chip select input. active low logic input. the device is selected when this input is active. 22 rd read input. active low logic input. this input is used in conjunction with cs low to enable the data outputs and read a conversion result from the ad7863. 23 busy busy output. the busy output is tri ggered high by the falling edge of convst and remains high until conversion is completed. 24 v dd analog and digital positive supply voltage, 5.0 v 5%. 25 v a1 input number 1 of channel a. analog input voltage rang es of 10 v (ad7863-10), 2.5 v (ad7863-3), and 0 v to 2.5 v (ad7863-2). 26 v b1 input number 1 of channel b. analog input voltage rang es of 10 v (ad7863-10), 2.5 v (ad7863-3), and 0 v to 2.5 v (ad7863-2). 27 agnd analog ground. ground reference for mux, track/hold, reference, and dac circuitry. 28 db13 data bit 13 (msb). three-state ttl output. output codi ng is twos complement for the ad7863-10 and ad7863-3. output coding is straight (natural) binary for the ad7863-2.
ad7863 rev. b | page 8 of 24 terminology signal-to-(noise + distortion) ratio this is the measured ratio of signal to (noise + distortion) at the output of the analog-to-digital converter. the signal is the rms amplitude of the fundamental. noise is the rms sum of all non- fundamental signals up to half the sampling frequency (f s /2), excluding dc. the ratio is dependent upon the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. the theoretical signal-to- (noise + distortion) ratio for an ideal n-bit converter with a sine wave input is given by signal to (noise + distortion) = (6.02n + 1.76) db for a 14-bit converter, this is 86.04 db. total harmonic distortion total harmonic distortion (thd) is the ratio of the rms sum of harmonics to the fundamental. for the ad7863 it is defined as () 1 5432 v vvvv dbthd 222 log20 +++ = 2 where: v 1 is the rms amplitude of the fundamental. v 2 , v 3 , v 4 , and v 5 are the rms amplitudes of the second through the fifth harmonics. peak harmonic or spurious noise peak harmonic or spurious noise is defined as the ratio of the rms value of the next largest component in the adc output spectrum (up to f s /2 and excluding dc) to the rms value of the fundamental. normally, the value of this specification is determined by the largest harmonic in the spectrum, but for parts where the harmonics are buried in the noise floor, it is a noise peak. intermodulation distortion with inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities creates distortion products at sum and difference frequencies of mfa nfb where m, n = 0, 1, 2, 3. intermodulation terms are those for which neither m nor n is equal to zero. for example, the second order terms include (fa + fb) and (fa ? fb), and the third order terms include (2fa + fb), (2fa ? fb), (fa + 2fb), and (fa ? 2fb). the ad7863 is tested using two input frequencies. in this case, the second and third order terms are of different significance. the second order terms are usually distanced in frequency from the original sine waves, and the third order terms are usually at a frequency close to the input frequencies. as a result, the second and third order terms are specified separately. the calculation of the intermodulation distortion is as per the thd specification where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the fundamental, expressed in decibels (db). channel-to-channel isolation channel-to-channel isolation is a measure of the level of crosstalk between channels. it is measured by applying a full- scale 50 khz sine wave signal to all nonselected channels and determining how much that signal is attenuated in the selected channel. the figure given is the worst case across all channels. relative accuracy relative accuracy or endpoint nonlinearity is the maximum deviation from a straight line passing through the endpoints of the adc transfer function. differential nonlinearity this is the difference between the measured and the ideal 1 lsb change between any two adjacent codes in the adc. positive gain error (ad7863-10, 10 v, ad7863-3, 2.5 v) this is the deviation of the last code transition (01 . . . 110 to 01 . . . 111) from the ideal 4 v ref ? 1 lsb (ad7863-10, 10 v range) or v ref ? 1 lsb (ad7863-3, 2.5 v range), after the bipolar offset error has been adjusted out. positive gain error (ad7863-2, 0 v to 2.5 v) this is the deviation of the last code transition (11 . . . 110 to 11 . . . 111) from the ideal v ref ? 1 lsb, after the unipolar offset error has been adjusted out. bipolar zero error (ad7863-10, 10 v, ad7863-3, 2.5 v) this is the deviation of the midscale transition (all 0s to all 1s) from the ideal 0 v (agnd). unipolar offset error (ad7863-2, 0 v to 2.5 v) this is the deviation of the first code transition (00 . . . 000 to 00 . . . 001) from the ideal agnd + 1 lsb. negative gain error (ad7863-10, 10 v, ad7863-3, 2.5 v) this is the deviation of the first code transition (10 . . . 000 to 10 . . . 001) from the ideal ?4 v ref + 1 lsb (ad7863-10, 10 v range) or Cv ref + 1 lsb (ad7863-3, 2.5 v range), after bipolar zero error has been adjusted out. track-and-hold acquisition time track-and-hold acquisition time is the time required for the output of the track/hold amplifier to reach its final value, with ? lsb, after the end of conversion (the point at which the track-and-hold returns to track mode). it also applies to situations where a change in the selected input channel takes place or where there is a step input change on the input voltage applied to the selected v ax/bx input of the ad7863. it means that the user must wait for the duration of the track-and-hold acquisition time after the end of conversion or after a channel change/step input change to v ax/bx before starting another conversion, to ensure that the part operates to specification.
ad7863 rev. b | page 9 of 24 converter details the ad7863 is a high speed, low power, dual 14-bit analog-to- digital converter that operates from a single 5 v supply. the part contains two 5.2 s successive approximation adcs, two track-and-hold amplifiers, an internal 2.5 v reference, and a high speed parallel interface. four analog inputs are grouped into two channels (a and b) selected by the a0 input. each channel has two inputs (v a1 and v a2 or v b1 and v b2 ) that can be sampled and converted simultaneously, thus preserving the relative phase information of the signals on both analog inputs. the part accepts an analog input range of 10 v (ad7863-10), 2.5 v (ad7863-3), and 0 v to 2.5 v (ad7863-2). overvoltage protection on the analog inputs for the part allows the input voltage to go to 17 v, 7 v, or +7 v, respectively, without causing damage. the ad7863 has two operating modes, the high sampling mode and the auto sleep mode, where the part auto- matically goes into sleep after the end of conversion. these modes are discussed in more detail in the timing and control section. conversion is initiated on the ad7863 by pulsing the convst input. on the falling edge of convst , both on-chip track-and- holds are simultaneously placed into hold and the conversion sequence is started on both channels. the conversion clock for the part is generated internally using a laser-trimmed clock oscillator circuit. the busy signal indicates the end of conversion and at this time the conversion results for both channels are available to be read. the first read after a conver- sion accesses the result from v a1 or v b1 , and the second read accesses the result from v a2 or v b2 , depending on whether the multiplexer select a0 is low or high, respectively, before the conversion is initiated. data is read from the part via a 14-bit parallel data bus with standard cs and rd signals. conversion time for the ad7863 is 5.2 s in the high sampling mode (10 s for the auto sleep mode), and the track/hold acquisition time is 0.5 s. to obtain optimum performance from the part, the read operation should not occur during the conversion or during the 400 ns prior to the next conversion. this allows the part to operate at throughput rates up to 175 khz and achieve data sheet specifications. track-and-hold section the track-and-hold amplifiers on the ad7863 allow the adcs to accurately convert an input sine wave of full-scale amplitude to 14-bit accuracy. the input bandwidth of the track-and-hold is greater than the nyquist rate of the adc, even when the adc is operated at its maximum throughput rate of 175 khz (that is, the track-and hold can handle input frequencies in excess of 87.5 khz). the track-and-hold amplifiers acquire input signals to 14-bit accuracy in less than 500 ns. the operation of the track-and- holds is essentially transparent to the user. the two track-and-hold amplifiers sample their respective input channels simultaneously, on the falling edge of convst . the aperture time for the track-and-holds (that is, the delay time between the external convst signal and the track-and-hold actually going into hold) is well-matched across the two track-and-holds on one device and also well-matched from device to device. this allows the relative phase information between different input channels to be accurately preserved. it also allows multiple ad7863s to simultaneously sample more than two channels. at the end of conversion, the part returns to its tracking mode. the acquisition time of the track-and-hold amplifiers begins at this point. reference section the ad7863 contains a single reference pin, labeled v ref , that provides access to the parts own 2.5 v reference. alternatively, an external 2.5 v reference can be connected to this pin, thus providing the reference source for the part. the part is specified with a 2.5 v reference voltage. errors in the reference source result in gain errors in the ad7863 transfer function and add to the specified full-scale errors on the part. on the ad7863-10 and ad7863-3, it also results in an offset error injected in the attenuator stage. the ad7863 contains an on-chip 2.5 v reference. to use this reference as the reference source for the ad7863, connect two 0.1 f disc ceramic capacitors from the v ref pin to agnd. the voltage that appears at this pin is internally buffered before being applied to the adc. if this reference is required for use external to the ad7863, it should be buffered because the part has a fet switch in series with the reference output resulting in a source impedance for this output of 5.5 k nominal. the tolerance on the internal reference is 10 mv at 25c with a typical temperature coefficient of 25 ppm/c and a maximum error over temperature of 25 mv. if the application requires a reference with a tighter tolerance or the ad7863 needs to be used with a system reference, the user has the option of connecting an external reference to this v ref pin. the external reference effectively overdrives the internal reference and thus provides the reference source for the adc. the reference input is buffered before being applied to the adc with a maximum input current of 100 a. a suitable reference source for the ad7863 is the ad780 precision 2.5 v reference.
ad7863 rev. b | page 10 of 24 circuit description analog input section the ad7863 is offered as three part types: the ad7863-10, which handles a 10 v input voltage range, the ad7863-3, which handles input voltage range 2.5 v and the ad7863-2, which handles a 0 v to 2.5 v input voltage range. 2.5v reference mux r2 r1 r3 to internal comparator track/ hold v ref v ax agnd ad7863-10/ad7863-3 2k ? to adc reference circuitry 06411-005 figure 5. ad7863-10/ad7863-3 analog input structure figure 5 shows the analog input section for the ad7863-10 and ad7863-3. the analog input range of the ad7863-10 is 10 v into an input resistance of typically 9 k. the analog input range of the ad7863-3 is 2.5 v into an input resistance of typically 3 k. this input is benign, with no dynamic charging currents because the resistor stage is followed by a high input impedance stage of the track-and-hold amplifier. for the ad7863-10, r1 = 8 k, r2 = 2 k and r3 = 2 k. for the ad7863-3, r1 = r2 = 2 k and r3 is open circuit. for the ad7863-10 and ad7863-3, the designed code transitions occur on successive integer lsb values (that is, 1 lsb, 2 lsbs, 3 lsbs . . .). output coding is twos complement binary with 1 lsb = fs/16,384. the ideal input/output transfer function for the ad7863-10 and ad7863-3 is shown in table 5 . table 5. ideal input/output code (ad7863-10/ad7863-3) analog input 1 digital output code transition +fsr/2 ? 1 lsb 2 011 . . . 110 to 011 . . . 111 +fsr/2 ? 2 lsbs 011 . . . 101 to 011 . . . 110 +fsr/2 ? 3 lsbs 011 . . . 100 to 011 . . . 101 gnd + 1 lsb 000 . . . 000 to 000 . . . 001 gnd 111 . . . 111 to 000 . . . 000 gnd ? 1 lsb 111 . . . 110 to 111 . . . 111 ?fsr/2 + 3 lsbs 100 . . . 010 to 100 . . . 011 ?fsr/2 + 2 lsbs 100 . . . 001 to 100 . . . 010 ?fsr/2 + 1 lsb 100 . . . 000 to 100 . . . 001 1 fsr is full-scale range = 20 v (ad7863-10) and = 5 v (ad7863-3) with v ref = 2.5 v. 2 1 lsb = fsr/16,384 = 1.22 mv (ad7863- 10) and 0.3 mv (ad7863-3) with v ref = 2.5 v. the analog input section for the ad7863-2 contains no biasing resistors and the v ax/bx pin drives the input directly to the multiplexer and track-and-hold amplifier circuitry. the analog input range is 0 v to 2.5 v into a high impedance stage with an input current of less than 100 na. this input is benign, with no dynamic charging currents. once again, the designed code transitions occur on successive integer lsb values. output coding is straight (natural) binary with 1 lsb = fs/16,384 = 2.5 v/16,384 = 0.15 mv. table 6 shows the ideal input/output transfer function for the ad7863-2. table 6. ideal input/output code (ad7863-2) analog input 1 digital output code transition +fsr ? 1 lsb 2 111 . . . 110 to 111 . . . 111 +fsr ? 2 lsb 111 . . . 101 to 111 . . . 110 +fsr ? 3 lsb 111 . . . 100 to 111 . . . 101 gnd + 3 lsb 000 . . . 010 to 000 . . . 011 gnd + 2 lsb 000 . . . 001 to 000 . . . 010 gnd + 1 lsb 000 . . . 000 to 000 . . . 001 1 fsr is full-scale range = 2.5 v for ad7863-2 with v ref = 2.5 v. 2 1 lsb = fsr/16,384 = 0.15 mv for ad7863-2 with v ref = 2.5 v. offset and full-scale adjustment in most digital signal processing (dsp) applications, offset and full-scale errors have little or no effect on system performance. offset error can always be eliminated in the analog domain by ac coupling. full-scale error effect is linear and does not cause problems as long as the input signal is within the full dynamic range of the adc. invariably, some applications require that the input signal span the full analog input dynamic range. in such applications, offset and full-scale error have to be adjusted to zero. figure 6 shows a typical circuit that can be used to adjust the offset and full-scale errors on the ad7863 (v a1 on the ad7863-10 version is shown for example purposes only). where adjustment is required, offset error must be adjusted before full-scale error. this is achieved by trimming the offset of the op amp driving the analog input of the ad7863 while the input voltage is ? lsb below analog ground. the trim procedure is as follows: apply a voltage of ?0.61 mv (?? lsb) at v 1 in figure 6 and adjust the op amp offset voltage until the adc output code flickers between 11 1111 1111 1111 and 00 0000 0000 0000. r2 500 ? *additional pins omitted for clarity. v a1 agnd ad7863* r1 10k ? r3 10k? r5 10k ? r4 10k ? v 1 input range = 10 v 06411-006 figure 6. full-sca le adjust circuit
ad7863 rev. b | page 11 of 24 gain error can be adjusted at either the first code transition (adc negative full scale) or the last code transition (adc positive full scale). the trim procedures for both cases are as follows: positive full-scale adjust (?10 version) apply a voltage of 9.9927 v (fs/2 C 1 lsbs) at v 1 . adjust r2 until the adc output code flickers between 01 1111 1111 1110 and 01 1111 1111 1111. negative full-scale adjust (?10 version) apply a voltage of ?9.9976 v (?fs + 1 lsb) at v 1 . adjust r2 until the adc output code flickers between 10 0000 0000 0000 and 10 0000 0000 0001. an alternative scheme for adjusting full-scale error in systems that use an external reference is to adjust the voltage at the v ref pin until the full-scale error for any of the channels is adjusted out. the good full-scale matching of the channels ensures small full-scale errors on the other channels. timing and control figure 7 shows the timing and control sequence required to obtain optimum performance (mode 1) from the ad7863. in the sequence shown, a conversion is initiated on the falling edge of convst . this places both track-and-holds into hold simultaneously and new data from this conversion is available in the output register of the ad7863 5.2 s later. the busy signal indicates the end of conversion and at this time the conversion results for both channels are available to be read. a second conversion is then initiated. if the multiplexer select (a0) is low, the first and second read pulses after the first conversion accesses the result from channel a (v a1 and v a2 , respectively). the third and fourth read pulses, after the second conversion and a0 high, accesses the result from channel b (v b1 and v b2 , respectively). the state of a0 can be changed any time after the convst goes high, that is, track-and-holds into hold and 500 ns prior to the next falling edge of convst . note that a0 should not be changed during conversion if the nonselected channels have negative voltages applied to them, which are outside the input range of the ad7863, because this affects the conversion in progress. data is read from the part via a 14-bit parallel data bus with standard cs and rd signal, that is, the read operation consists of a negative going pulse on the cs pin combined with two negative going pulses on the rd pin (while the cs is low), accessing the two 14-bit results. once the read operation has taken place, a further 400 ns should be allowed before the next falling edge of convst to optimize the settling of the track- and-hold amplifier before the next conversion is initiated. the achievable throughput rate for the part is 5.2 s (conversion time) plus 100 ns (read time) plus 0.4 s (quiet time). this results in a minimum throughput time of 5.7 s (equivalent to a throughput rate of 175 khz). v a1 v a2 v b1 v b2 c onvst busy a0 cs rd data t conv = 5.2s 06411-007 t 3 t 8 t acq t 1 t 4 t 2 t 5 t 6 t 7 figure 7. mode 1 timing operation diagram for high sampling performance
ad7863 rev. b | page 12 of 24 read options apart from the read operation previously described and displayed in figure 7 , other cs and rd combinations can result in different channels/inputs being read in different combinations. suitable combinations are shown in figure 8 , figure 9 , and figure 10 . 06411-008 v a1 v a2 cs rd data figure 8. read option a (a0 is low) 06411-009 cs rd data v a1 v a2 v a1 figure 9. read option b (a0 is low) 0 6411-010 a0 cs rd dat a v a1 v a2 figure 10. read option c
ad7863 rev. b | page 13 of 24 operating modes mode 1 operation normal power, high sampling performance the timing diagram in figure 7 is for optimum performance in operating mode 1 where the falling edge of convst starts conversion and puts the track-and-hold amplifiers into their hold mode. this falling edge of convst also causes the busy signal to go high to indicate th at a conversion is taking place. the busy signal goes low when the conversion is complete, which is 5.2 s max after the falling edge of convst and new data from this conversion is available in the output latch of the ad7863. a read operation accesses this data. if the multiplexer select a0 is low, the first and second read pulses after the first conversion accesses the result from channel a (v a1 and v a2 , respectively). the third and fourth read pulses, after the second conversion and a0 high, access the result from channel b (v b1 and v b2 , respectively). data is read from the part via a 14-bit parallel data bus with standard cs and rd signals. this data read operation consists of a negative going pulse on the cs pin combined with two negative going pulses on the rd pin (while the cs is low), accessing the two 14-bit results. for the fastest throughput rate the read operation takes 100 ns. the read operation must be complete at least 400 ns before the falling edge of the next convst and this gives a total time of 5.7 s for the full throughput time (equivalent to 175 khz). this mode of operation should be used for high sampling applications. mode 2 operation power-down, auto-sleep after conversion the timing diagram in figure 11 is for optimum performance in operating mode 2 where the part automatically goes into sleep mode once busy goes low after conversion and wakes up before the next conversion takes place. this is achieved by keeping convst low at the end of the second conversion, whereas it was high at the end of the second conversion for mode 1 operation. the operation shown in figure 11 shows how to access data from both channel a and channel b, followed by the auto sleep mode. one can also set up the timing to access data from channel a only or channel b only (see the read options section) and then go into auto sleep mode. the rising edge of convst wakes up the part. this wake-up time is 4.8 s when using an external reference and 5 ms when using the internal reference, at which point the track-and-hold amplifiers go into their hold mode, provided the convst has gone low. the conversion takes 5.2 s after this giving a total of 10 s (external reference, 5.005 ms for internal reference) from the rising edge of convst to the conversion being complete, which is indicated by the busy going low. note that because the wake-up time from the rising edge of convst is 4.8 s, if the convst pulse width is greater than 5.2 s the conversion takes more than the 10 s (4.8 s wake-up time + 5.2 s conversion time) shown in figure 11 from the rising edge of convst . this is because the track-and-hold amplifiers go into their hold mode on the falling edge of convst and the conversion does not complete for a further 5.2 s. in this case, the busy is the best indicator of when the conversion is complete. even though the part is in sleep mode, data can still be read from the part. the read operation is identical to that in mode 1 operation and must also be complete at least 400 ns before the falling edge of the next convst to allow the track-and-hold amplifiers to have enough time to settle. this mode is very useful when the part is converting at a slow rate because the power consumption is significantly reduced from that of mode 1 operation. v a1 v a2 convst busy a0 cs rd data * when using an external reference, wake-up time = 4.8s. ** when using an internal reference, wake-up time = 5ms. 4.8s*/5ms** wake-up time t 3 t 3 t conv = 5.2s t conv = 5.2s v b1 v b2 t 8 t acq 06411-011 figure 11. mode 2 timing diagram where automatic sleep function is initiated
ad7863 rev. b | page 14 of 24 ad7863 dynamic specifications the ad7863 is specified and tested for dynamic performance as well as traditional dc specifications such as integral and differential nonlinearity. these ac specifications are required for the signal processing applications such as phased array sonar, adaptive filters, and spectrum analysis. these applications require information on the adcs effect on the spectral content of the input signal. hence, the parameters for which the ad7863 is specified include snr, harmonic distortion, intermodulation distortion, and peak harmonics. these terms are discussed in more detail in the following sections. signal-to-noise ratio (snr) snr is the measured signal-to-noise ratio at the output of the adc. the signal is the rms magnitude of the fundamental. noise is the rms sum of all the nonfundamental signals up to half the sampling frequency (f s /2), excluding dc; snr is dependent upon the number of quantization levels used in the digitization process; the more levels, the smaller the quantization noise. the theoretical signal-to-noise ratio for a sine wave input is given by snr = (6.02n + 1.76) db (1) where n is the number of bits. thus for an ideal 14-bit converter, snr = 86.04 db. figure 12 shows a histogram plot for 8192 conversions of a dc input using the ad7863 with 5 v supply. the analog input was set at the center of a code transition. it can be seen that the codes appear mainly in the one output bin, indicating very good noise performance from the adc. 746 747 748 749 750 751 752 753 754 755 06411-012 counts code 8000 7000 6000 5000 4000 3000 2000 1000 0 figure 12. histogram of 8192 conversions of a dc input the output spectrum from the adc is evaluated by applying a sine wave signal of very low distortion to the v ax/bx input, which is sampled at a 175 khz sampling rate. a fast fourier transform (fft) plot is generated from which the snr data can be obtained. figure 13 shows a typical 8192 point fft plot of the ad7863 with an input signal of 10 khz and a sampling frequency of 175 khz. the snr obtained from this graph is ?80.72 db. it should be noted that the harmonics are taken into account when calculating the snr. 0 102030405060708090 06411-013 (db) frequency (khz) 0 ?130 ?120 ?110 ?100 ?90 ?80 ?70 ?60 ?50 ?40 ?30 ?20 ?10 ?140 ?150 f sample = 175khz f in = 10khz snr = +80.72db thd = ?92.96db figure 13. ad7863 fft plot effective number of bits the formula given in equation 1 relates the snr to the number of bits. rewriting the formula, as in equation 2, it is possible to obtain a measure of performance expressed in effective number of bits (n). 02.6 76.1 ? = snr n (2) the effective number of bits for a device can be calculated directly from its measured snr. figure 14 shows a typical plot of effective numbers of bits vs. frequency for an ad7863-2 with a sampling frequency of 175 khz. the effective number of bits typically falls between 13.11 and 11.05 corresponding to snr figures of 80.68 db and 68.28 db. 0 200 400 600 800 1000 06411-014 enob frequency (khz) 14.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5 10.0 figure 14. effective numbers of bits vs. frequency
ad7863 rev. b | page 15 of 24 total harmonic distortion (thd) total harmonic distortion (thd) is the ratio of the rms sum of harmonics to the rms value of the fundamental. for the ad7863, thd is defined as () 1 5432 v vvvv dbthd 2222 log20 +++ = (3) where: v 1 is the rms amplitude of the fundamental. v 2 , v 3 , v 4 , and v 5 are the rms amplitudes of the second through the fifth harmonic. thd is also derived from the fft plot of the adc output spectrum. intermodulation distortion with inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities creates distortion products at sum and difference frequencies of mfa nfb where m, n = 0, 1, 2, 3 . . . intermodulation terms are those for which neither m nor n is equal to zero. for example, the second order terms include (fa + fb) and (fa ? fb) and the third order terms include (2fa + fb), (2fa ? fb), (fa + 2fb), and (fa ? 2fb). in this case, the second and third order terms are of different significance. the second order terms are usually distanced in frequency from the original sine waves while the third order terms are usually at a frequency close to the input frequencies. as a result, the second and third order terms are specified separately. the calculation of the intermodulation distortion is as per the thd specification where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the fundamental expressed in dbs. in this case, the input consists of two equal amplitude, low distortion sine waves. figure 15 shows a typical imd plot for the ad7863. 0 102030405060708090 06411-015 (db) freuency (khz) 0 130 120 110 100 90 80 70 60 50 40 30 20 10 140 150 input freuencies f1 = 50.13khz f2 = 49.13khz f sample = 175khz imd 2nd order term 98.21db 3rd order term 93.91db figure 15. imd plot peak harmonic or spurious noise harmonic or spurious noise is defined as the ratio of the rms value of the next largest component in the adc output spectrum (up to f s /2 and excluding dc) to the rms value of the fundamental. normally, the value of this specification is determined by the largest harmonic in the spectrum, but for parts where the harmonics are buried in the noise floor, the peak is a noise peak. dc linearity plot figure 16 and figure 17 show typical dnl and inl plots for the ad7863. 0 2048 4096 6144 8192 10240 12288 14336 16383 06411-016 dnl error (lsb) adc code 1.0 0.5 0 0.5 1.0 figure 16. dc dnl plot 0 2048 4096 6144 8192 10240 12288 14336 16383 06411-017 inl error (lsb) adc code 1.0 0.5 0 0.5 1.0 figure 17. dc inl plot
ad7863 rev. b | page 16 of 24 power considerations in the automatic power-down mode the part can be operated at a sample rate that is considerably less than 175 khz. in this case, the power consumption is reduced and depends on the sample rate. figure 18 shows a graph of the power consumption vs. sampling rates from 1 hz to 100 khz in the automatic power- down mode. the conditions are 5 v supply at 25c. 06411-018 power (mw) frequency (khz) 50 0 0 102030405060708090100 45 40 35 30 25 20 15 10 5 figure 18. power vs. sample rate in auto power-down
ad7863 rev. b | page 17 of 24 microprocessor interfacing the ad7863 high speed bus timing allows direct interfacing to dsp processors as well as modern 16-bit microprocessors. suitable microprocessor interfaces are shown in figure 19 through figure 23 . ad7863 to adsp-2100 interface figure 19 shows an interface between the ad7863 and the adsp-2100. the convst signal can be supplied from the adsp-2100 or from an external source. the ad7863 busy line provides an interrupt to the adsp-2100 when conversion is completed on both channels. the two conversion results can then be read from the ad7863 using two successive reads to the same memory address. the following instruction reads one of the two results: mr0 = dm (adc) where: mr0 is the adsp-2100 mr0 register. adc is the ad7863 address. addr decode en address bus dma13 dma0 dms irqn dmrd (rd) dmd15 dmd0 cs a0 busy rd db13 db0 data bus adsp-2100 (adsp-2101/ adsp-2102) ad7863* *additional pins omitted for clarity. optional convst 06411-019 figure 19. ad7863 to adsp-2100 interface ad7863 to adsp-2101/ad sp-2102 interface the interface outlined in figure 19 also forms the basis for an interface between the ad7863 and the adsp-2101/adsp-2102. the read line of the adsp-2101/adsp-2102 is labeled rd . in this interface, the rd pulse width of the processor can be programmed using the data memory wait state control register. the instruction used to read one of the two results is as outlined for the adsp-2100. ad7863 to tms32010 interface an interface between the ad7863 and the tms32010 is shown in figure 20 . once again the convst signal can be supplied from the tms32010 or from an external source, and the tms32010 is interrupted when both conversions have been completed. the following instruction is used to read the conversion results from the ad7863: in d, adc where: d is data memory address. adc is the ad7863 address. address decode en address bus pa2 pa0 men int den d15 d0 cs a0 busy rd db13 db0 data bus tms32010 ad7863* *additional pins omitted for clarity. optional convst 0 6411-020 figure 20. ad7863 to tms32010 interface ad7863 to tms320c25 interface figure 21 shows an interface between the ad7863 and the tms320c25. as with the two prev ious interfaces, conversion can be initiated from the tms320c25 or from an external source, and the processor is interrupted when the conversion sequence is completed. the tms320c25 does not have a separate rd output to drive the ad7863 rd input directly. this has to be generated from the processor strb and r/ w outputs with the addition of some logic gates. the rd signal is or gated with the msc signal to provide the one wait state required in the read cycle for correct interface timing. conversion results are read from the ad7863 using the following instruction: in d, adc where: d is data memory address. adc is the ad7863 address.
ad7863 rev. b | page 18 of 24 address decode en address bus cs a0 busy rd db13 db0 data bus ad7863* *additional pins omitted for clarity. optional convst 06411-021 tms320c25 a15 a0 is intn strb r/w dmd15 dmd0 ready msc figure 21. ad7863 to tms320c25 interface some applications may require that the conversion be initiated by the microprocessor rather than an external timer. one option is to decode the ad7863 convst from the address bus so that a write operation starts a conversion. data is read at the end of the conversion sequence as before. figure 23 shows an example of initiating conversion using this method. note that for all interfaces, it is preferred that a read operation not be attempted during conversion. ad7863 to mc68000 interface an interface between the ad7863 and the mc68000 is shown in figure 22 . as before, conversion can be supplied from the mc68000 or from an external source. the ad7863 busy line can be used to interrupt the processor or, alternatively, software delays can ensure that conversion has been completed before a read to the ad7863 is attempted. because of the nature of its interrupts, the mc68000 requires additional logic (not shown in figure 23 ) to allow it to be interrupted correctly. for further information on mc68000 interrupts, consult the mc68000 users manual. the mc68000 as and r/ w outputs are used to generate a separate rd input signal for the ad7863. cs is used to drive the mc68000 dtack input to allow the processor to execute a normal read operation to the ad7863. the conversion results are read using the following mc68000 instruction: move.w adc, d0 where: d0 is the 68000 d 0 register. adc is the ad7863 address. address decode en address bus a15 a0 dtack as d15 d0 cs a0 rd db13 db0 data bus mc68000 ad7863* *additional pins omitted for clarity. optional convst 06411-022 r/w figure 22. ad7863 to mc68000 interface ad7863 to 80c196 interface figure 23 shows an interface between the ad7863 and the 80c196 microprocessor. here, the microprocessor initiates conversion. this is achieved by gating the 80c196 wr signal with a decoded address output (different from the ad7863 cs address). the ad7863 busy line is used to interrupt the microprocessor when the conversion sequence is completed. address decode en address bus a15 a1 d15 d0 cs a0 busy db13 db0 data bus 80c196 ad7863* *additional pins omitted for clarity. 06411-023 wr rd rd figure 23. ad7863C80c196 interface vector motor control the current drawn by a motor can be split into two components: one produces torque and the other produces magnetic flux. for optimal performance of the motor, these two components should be controlled independently. in conventional methods of controlling a three-phase motor, the current (or voltage) supplied to the motor and the frequency of the drive are the basic control variables. however, both the torque and flux are functions of current (or voltage) and frequency. this coupling effect can reduce the performance of the motor because, for example, if the torque is increased by increasing the frequency, the flux tends to decrease.
ad7863 rev. b | page 19 of 24 vector control of an ac motor involves controlling the phase in addition to drive and current frequency. controlling the phase of the motor requires feedback information on the position of the rotor relative to the rotating magnetic field in the motor. using this information, a vector controller mathematically transforms the three phase drive currents into separate torque and flux components. the ad7863 is ideally suited for use in vector motor control applications. a block diagram of a vector motor control application using the ad7863 is shown in figure 24 . the position of the field is derived by determining the current in each phase of the motor. only two phase currents need to be measured because the third can be calculated if two phases are known. v a1 and v a2 of the ad7863 are used to digitize this information. simultaneous sampling is critical to maintaining the relative phase information between the two channels. a current sensing isolation amplifier, transformer, or hall effect sensor is used between the motor and the ad7863. rotor information is obtained by measuring the voltage from two of the inputs to the motor. v b1 and v b2 of the ad7863 are used to obtain this information. once again the relative phase of the two channels is important. a dsp microprocessor is used to perform the mathematical transformations and control loop calculations on the information fed back by the ad7863. dsp microprocessor dac drive circuitry i c i b i a v b v a isolation amplifiers voltage attenuators torque setpoint flux setpoint *additional pins omitted for clarity. dac dac ad7863* v a1 v a2 v b1 v b2 06411-024 torque and flux control loop calculations and two to three phase information transformation to torque and flux current components three phase motor figure 24. vector motor control using the ad7863 multiple ad7863s figure 25 shows a system where a number of ad7863s can be configured to handle multiple input channels. this type of configuration is common in applications such as sonar and radar. the ad7863 is specified with typical limits on aperture delay. this means that the user knows the difference in the sampling instant between all channels. this allows the user to maintain relative phase information between the different channels. v a1 v b1 v a2 v b2 v a1 v b1 v a2 v b2 06411-025 v a1 v b1 v a2 v b2 ad7863 (1) v ref rd cs ad7863 (2) ad7863 (n) address decode address v ref v ref rd rd cs rd cs figure 25. multiple ad7863s in multichannel system a common read signal from the microprocessor drives the rd input of all ad7863s. each ad7863 is designated a unique address selected by the address decoder. the reference output of ad7863 number 1 is used to drive the reference input of all other ad7863s in the circuit shown in figure 25 . one v ref can be used to provide the reference to several other ad7863s. alternatively, an external or system reference can be used to drive all v ref inputs. a common reference ensures good full- scale tracking between all channels.
ad7863 rev. b | page 20 of 24 applications hints pc board layout considerations the ad7863 is optimally designed for lowest noise performance, both radiated and conducted noise. to complement the excellent noise performance of the ad7863 it is imperative that great care be given to the pc board layout. figure 26 shows a recommended connection diagram for the ad7863. ground planes the ad7863 and associated analog circuitry should have a separate ground plane, referred to as the analog ground plane (agnd). this analog ground plane should encompass all ad7863 ground pins (including the dgnd pin), voltage reference circuitry, power supply bypass circuitry, the analog input traces, and any associated input/buffer amplifiers. the regular pcb ground plane (referred to as the dgnd for this discussion) area should encompass all digital signal traces, excluding the ground pins, leading up to the ad7863. power planes the pc board layout should have two distinct power planes, one for analog circuitry and one for digital circuitry. the analog power plane should encompass the ad7863 (v dd ) and all associated analog circuitry. this power plane should be connected to the regular pcb power plane (v cc ) at a single point, if necessary through a ferrite bead, as illustrated in figure 26 . this bead (part numbers for reference: fair-rite 274300111 or murata bl01/02/03) should be located within three inches of the ad7863. the pcb power plane (v cc ) should provide power to all digital logic on the pc board, and the analog power plane (v dd ) should provide power to all ad7863 power pins, voltage reference circuitry and any input amplifiers, if needed. a suitable low noise amplifier for the ad7863 is the ad797, one for each input. ensure that the +v s and the ?v s supplies to each amplifier are individually decoupled to agnd. the pcb power (v cc ) and ground (dgnd) should not overlay portions of the analog power plane (v dd ). keeping the v cc power and the dgnd planes from overlaying the v dd contributes to a reduction in plane-to-plane noise coupling. supply decoupling noise on the analog power plane (v dd ) can be further reduced by use of multiple decoupling capacitors ( figure 26 ). optimum performance is achieved by the use of disc ceramic capacitors. the v dd and reference pins (whether using an external or an internal reference) should be individually decoupled to the analog ground plane (agnd). this should be done by placing the capacitors as close as possible to the ad7863 pins with the capacitor leads as short as possible, thus minimizing lead inductance. ad7863 agnd dgnd agnd ad780 l (ferrite bead) temp +15v v a1 v b1 v a2 v b2 v a1 v ref v in v out v dd v b1 v a2 v b2 0.1f 0.1f 0.1f 0.1f 10f 47f analog supply +5v analog supply ?15v 0.1f ?v s 4 ad797s +v s 0.1f 06411-026 figure 26. typical connections diagra m including the relevant decoupling
ad7863 rev. b | page 21 of 24 outline dimensions controlling dimensions are in millimeters; inch dimensions (in parentheses) are rounded-off millimeter equivalents for reference only and are not appropriate for use in design. compliant to jedec standards ms-013-ae 18.10 (0.7126) 17.70 (0.6969) 0.30 (0.0118) 0.10 (0.0039) 2.65 (0.1043) 2.35 (0.0925) 10.65 (0.4193) 10.00 (0.3937) 7.60 (0.2992) 7.40 (0.2913) 0 . 7 5 ( 0 . 0 2 9 5 ) 0 . 2 5 ( 0 . 0 0 9 8 ) 45 1.27 (0.0500) 0.40 (0.0157) coplanarity 0.10 0.33 (0.0130) 0.20 (0.0079) 0.51 (0.0201) 0.31 (0.0122) seating plane 8 0 28 15 14 1 1.27 (0.0500) bsc 060706-a figure 27. 28-lead standard small outline package [soic_w] wide body (rw-28) dimensions shown in millimeters and (inches) compliant to jedec standards mo-150-ah 060106-a 28 15 14 1 10.50 10.20 9.90 8.20 7.80 7.40 5.60 5.30 5.00 seating plane 0.05 min 0.65 bsc 2.00 max 0.38 0.22 coplanarity 0.10 1.85 1.75 1.65 0.25 0.09 0.95 0.75 0.55 8 4 0 figure 28. 28-lead shrink small outline package [ssop] (rs-28) dimensions shown in millimeters
ad7863 rev. b | page 22 of 24 ordering guide model input range relative accuracy temperature range package description package option ad7863ar-10 10 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ar-10reel 10 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ar-10reel7 10 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863arz-10 1 10 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863arz-10reel 1 10 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863arz-10reel7 1 10 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ars-10 10 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 AD7863ARS-10REEL 10 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 AD7863ARS-10REEL7 10 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863arsz-10 1 10 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863arsz-10reel 1 10 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863arsz-10reel7 1 10 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863br-10 10 v 2.0 lsb C40c to +85c 28-lead soic_w rw-28 ad7863br-10reel 10 v 2.0 lsb C40c to +85c 28-lead soic_w rw-28 ad7863br-10reel7 10 v 2.0 lsb C40c to +85c 28-lead soic_w rw-28 ad7863brz-10 1 10 v 2.0 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ar-3 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ar-3reel 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ar-3reel7 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863arz-3 1 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ars-3 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863ars-3reel 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863ars-3reel7 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863arsz-3 1 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863arsz-3reel 1 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863arsz-3reel7 1 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863br-3 2.5 v 2.0 lsb C40c to +85c 28-lead soic_w rw-28 ad7863br-3reel 2.5 v 2.0 lsb C40c to +85c 28-lead soic_w rw-28 ad7863br-3reel7 2.5 v 2.0 lsb C40c to +85c 28-lead soic_w rw-28 ad7863brz-3 1 2.5 v 2.0 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ar-2 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ar-2reel 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ar-2reel7 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863arz-2 1 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863arz-2reel 1 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863arz-2reel7 1 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead soic_w rw-28 ad7863ars-2 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863ars-2reel 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863ars-2reel7 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863arsz-2 1 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863arsz-2reel 1 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 ad7863arsz-2reel7 1 0 v to 2.5 v 2.5 lsb C40c to +85c 28-lead ssop rs-28 eval-ad7863cb evaluation board 1 z = pb-free part.
ad7863 rev. b | page 23 of 24 notes
ad7863 rev. b | page 24 of 24 notes ?2006 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. d06411-0-11/06(b)

▲Up To Search▲

Price & Availability of AD7863ARS-10REEL

	To Download AD7863ARS-10REEL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .